Why Learning Essential Plumbing Skills is Vital for Bathtub Installation
Why Learning Essential Plumbing Skills is Vital for Bathtub Installation
Blog Article
What're your ideas about Tools You Need to Install a New Bathtub ?
Mounting a bathtub isn't exactly rocket science, but it does require strong plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is also a reasonably difficult job. If the old bathtub is readily easily accessible, the project can move rapidly; if you have to open up a wall surface to eliminate the old tub and position the new tub, the task is much harder. In either instance, the job is within a house handyman's abilities, although you will certainly need a helper to move out the old bathtub as well as embeded in the new one. Make sure you have qualified on your own for the job and also fit trying it. As opposed to hiring a specialist to take over a halfway-completed task, it is far better to consider utilizing one prior to you begin. Chances are you may need an expert plumber to make tube connections.
This short article will certainly aid you mount a new tub in your restroom if you have already gotten a new tub as well as don't need to alter the setup of your previous water supply pipelines.
Your tools and material list must comprise the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the supply of water. After doing so, activate the taps to drain pipes any type of water staying in the system. The procedure of eliminating the existing faucets can be rather troublesome as a result of the limited access that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will originate from the pipes. Once the supply pipes have actually been removed, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this process. As soon as the taps have been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before moving on to fit the new faucets, contrast the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end gives a link to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin ensuring that the washing machines remain in location between the tap as well as the sink. Secure the faucet in place with the maker offered backnut. As soon as the tap is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be linked to the tap ends initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using the two wood boards under its feet, place the bathtub in the required placement. The wooden boards are useful in equally spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four small factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by examining the level and changing the feet on the bath tub up until the spirit level reads level.
To mount faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipeline by making a compression join; then do the very same for the various other tap.
Turn on the water as well as inspect all joints and new pipework for leaks and also tighten them if essential. Load the tub as well as likewise check the overflow electrical outlet and also the regular outlet for leaks.
Ultimately, take care of the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bathtub must wait until the bathtub has actually been used at least once as this will resolve it right into its final position.
Preparing for the Installment
First of all, the sustaining framework provided with the bathroom needs to be fitted (if called for) according to the maker's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to make sure that if the tap includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the taps unit to stop strain on the bath tub.
Fit the versatile tap adapters to the bottom of the two taps utilizing 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath should now prepare to be suited its final setting.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break a rigid seal, triggering the water to permeate the wall in between the bathroom and also the tiling, leading to complications with wetness and also possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes as well as cartridges, and also are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Remember to constantly fill up the bath tub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealer can crack rather early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly offered on the market. It is advisable to fit the floor tiles making use of waterproof or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were made aware of that editorial on Installing A Bathtub from an associate on our other website. Are you aware of somebody else who is very much interested in the subject? Please feel free to share it. I take joy in reading our article about Tools You Need to Install a New Bathtub .
Reliable plumber? Dial now! Report this page